Subversion Repositories Tronxy-X3A-Marlin

/**

 * Marlin 3D Printer Firmware

 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]

 *

 * Based on Sprinter and grbl.

 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm

 *

 * This program is free software: you can redistribute it and/or modify

 * it under the terms of the GNU General Public License as published by

 * the Free Software Foundation, either version 3 of the License, or

 * (at your option) any later version.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 *

 * You should have received a copy of the GNU General Public License

 * along with this program.  If not, see <http://www.gnu.org/licenses/>.

 *

 */

/**

 * Einsy-Retro pin assignments

 */

#ifndef __AVR_ATmega2560__

  #error "Oops!  Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu."

#endif

#define BOARD_NAME         "Einsy Retro"

//

// TMC2130 Configuration_adv defaults for EinsyRetro

//

#if !AXIS_DRIVER_TYPE(X, TMC2130) || !AXIS_DRIVER_TYPE(Y, TMC2130) || !AXIS_DRIVER_TYPE(Z, TMC2130) || !AXIS_DRIVER_TYPE(E0, TMC2130)

  #error "You must set ([XYZ]|E0)_DRIVER_TYPE to TMC2130 in Configuration.h for EinsyRetro."

#endif

// TMC2130 Diag Pins (currently just for reference)

#define X_DIAG_PIN         64

#define Y_DIAG_PIN         69

#define Z_DIAG_PIN         68

#define E0_DIAG_PIN        65

//

// Limit Switches

//

// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers.

// Otherwise use a physical endstop based configuration.

//

// SERVO0_PIN and Z_MIN_PIN configuration for BLTOUCH sensor when combined with SENSORLESS_HOMING.

//

#if DISABLED(SENSORLESS_HOMING)

  #define X_MIN_PIN        12

  #define Y_MIN_PIN        11

  #define Z_MIN_PIN        10

  #define X_MAX_PIN        81

  #define Y_MAX_PIN        57

#else

  #if X_HOME_DIR == -1

    #define X_MIN_PIN      X_DIAG_PIN

    #define X_MAX_PIN      81

  #else

    #define X_MIN_PIN      12

    #define X_MAX_PIN      X_DIAG_PIN

  #endif

  #if Y_HOME_DIR == -1

    #define Y_MIN_PIN      Y_DIAG_PIN

    #define Y_MAX_PIN      57

  #else

    #define Y_MIN_PIN      11

    #define Y_MAX_PIN      Y_DIAG_PIN

  #endif

  #if ENABLED(BLTOUCH)

    #define Z_MIN_PIN      11   // Y-MIN

    #define SERVO0_PIN     10   // Z-MIN

  #else

    #define Z_MIN_PIN      10

  #endif

#endif

#define Z_MAX_PIN           7

//

// Z Probe (when not Z_MIN_PIN)

//

#ifndef Z_MIN_PROBE_PIN

  #define Z_MIN_PROBE_PIN  10

#endif

//

// Steppers

//

#define X_STEP_PIN         37

#define X_DIR_PIN          49

#define X_ENABLE_PIN       29

#define X_CS_PIN           41

#define Y_STEP_PIN         36

#define Y_DIR_PIN          48

#define Y_ENABLE_PIN       28

#define Y_CS_PIN           39

#define Z_STEP_PIN         35

#define Z_DIR_PIN          47

#define Z_ENABLE_PIN       27

#define Z_CS_PIN           67

#define E0_STEP_PIN        34

#define E0_DIR_PIN         43

#define E0_ENABLE_PIN      26

#define E0_CS_PIN          66

//

// Temperature Sensors

//

#define TEMP_0_PIN          0   // Analog Input

#define TEMP_1_PIN          1   // Analog Input

#define TEMP_BED_PIN        2   // Analog Input

//

// Heaters / Fans

//

#define HEATER_0_PIN        3

#define HEATER_BED_PIN      4

#ifndef FAN_PIN

  #define FAN_PIN           8

#endif

#define FAN1_PIN            6

//

// Misc. Functions

//

#define SDSS               53

#define LED_PIN            13

#define CASE_LIGHT_PIN      9

//

// M3/M4/M5 - Spindle/Laser Control

//

// use P1 connector for spindle pins

#define SPINDLE_LASER_PWM_PIN     9   // MUST BE HARDWARE PWM

#define SPINDLE_LASER_ENABLE_PIN 18   // Pin should have a pullup!

#define SPINDLE_DIR_PIN          19

//

// Průša i3 MK2 Multiplexer Support

//

#define E_MUX0_PIN         17

#define E_MUX1_PIN         16

#define E_MUX2_PIN         78   // 84 in MK2 Firmware, with BEEPER as 78

//

// LCD / Controller

//

#if ENABLED(ULTRA_LCD)

  #define KILL_PIN         32

  #if ENABLED(NEWPANEL)

    #if ENABLED(CR10_STOCKDISPLAY)

      #define LCD_PINS_RS     85

      #define LCD_PINS_ENABLE 71

      #define LCD_PINS_D4     70

      #define BTN_EN1         18

      #define BTN_EN2         19

    #else

      #define LCD_PINS_RS     82

      #define LCD_PINS_ENABLE 18

      #define LCD_PINS_D4     19

      #define LCD_PINS_D5     70

      #define LCD_PINS_D6     85

      #define LCD_PINS_D7     71

      #define BTN_EN1         14

      #define BTN_EN2         72

    #endif

    #define BTN_ENC            9   // AUX-2

    #define BEEPER_PIN        84   // AUX-4

    #define SD_DETECT_PIN     15

  #endif // NEWPANEL

#endif // ULTRA_LCD