Subversion Repositories Tronxy-X3A-Marlin

/**

 * Marlin 3D Printer Firmware

 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]

 *

 * Based on Sprinter and grbl.

 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm

 *

 * This program is free software: you can redistribute it and/or modify

 * it under the terms of the GNU General Public License as published by

 * the Free Software Foundation, either version 3 of the License, or

 * (at your option) any later version.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 *

 * You should have received a copy of the GNU General Public License

 * along with this program.  If not, see <http://www.gnu.org/licenses/>.

 *

 */

/**

 * Sanguinololu board pin assignments

 */

/**

 * Rev B    26 DEC 2016

 *

 * 1) added pointer to a current Arduino IDE extension

 * 2) added support for M3, M4 & M5 spindle control commands

 * 3) added case light pin definition

 *

 */

/**

 * A useable Arduino IDE extension (board manager) can be found at

 * https://github.com/Lauszus/Sanguino

 *

 * This extension has been tested on Arduino 1.6.12 & 1.8.0

 *

 * Here's the JSON path:

 * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json

 *

 * When installing select 1.0.2

 *

 * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino

 * Just use the above JSON URL instead of Sparkfun's JSON.

 *

 * Once installed select the Sanguino board and then select the CPU.

 *

 */

#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)

  #error "Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."

#endif

#ifndef BOARD_NAME

  #define BOARD_NAME "Sanguinololu <1.2"

#endif

//

// Limit Switches

//

#define X_STOP_PIN         18

#define Y_STOP_PIN         19

#define Z_STOP_PIN         20

//

// Steppers

//

#define X_STEP_PIN         15

#define X_DIR_PIN          21

#define Y_STEP_PIN         22

#define Y_DIR_PIN          23

#define Z_STEP_PIN          3

#define Z_DIR_PIN           2

#define E0_STEP_PIN         1

#define E0_DIR_PIN          0

//

// Temperature Sensors

//

#define TEMP_0_PIN          7   // Analog Input (pin 33 extruder)

#define TEMP_BED_PIN        6   // Analog Input (pin 34 bed)

//

// Heaters / Fans

//

#define HEATER_0_PIN       13   // (extruder)

#if ENABLED(SANGUINOLOLU_V_1_2)

  #define HEATER_BED_PIN   12   // (bed)

  #define X_ENABLE_PIN     14

  #define Y_ENABLE_PIN     14

  #define Z_ENABLE_PIN     26

  #define E0_ENABLE_PIN    14

  #if !defined(FAN_PIN) && ENABLED(LCD_I2C_PANELOLU2)

    #define FAN_PIN         4   // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan

  #endif

#else

  #define HEATER_BED_PIN   14   // (bed)

  #define X_ENABLE_PIN     -1

  #define Y_ENABLE_PIN     -1

  #define Z_ENABLE_PIN     -1

  #define E0_ENABLE_PIN    -1

#endif

#if !defined(FAN_PIN) && (MB(AZTEEG_X1) || MB(STB_11) || ENABLED(IS_MELZI))

  #define FAN_PIN           4   // Works for Panelolu2 too

#endif

//

// Misc. Functions

//

/**

 * In some versions of the Sanguino libraries the pin

 * definitions are wrong, with SDSS = 24 and LED_PIN = 28 (Melzi).

 * If you encounter issues with these pins, upgrade your

 * Sanguino libraries! See #368.

 */

//#define SDSS               24

#define SDSS               31

#if ENABLED(IS_MELZI)

  #define LED_PIN          27

#elif MB(STB_11)

  #define LCD_BACKLIGHT_PIN 17   // LCD backlight LED

#endif

#if DISABLED(SPINDLE_LASER_ENABLE) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL))  // try to use IO Header

  #define CASE_LIGHT_PIN     4   // MUST BE HARDWARE PWM  - see if IO Header is available

#endif

/**

 * Sanguinololu 1.4 AUX pins:

 *

 *           PWM  TX1  RX1  SDA  SCL

 *  12V  5V  D12  D11  D10  D17  D16

 *  GND GND  D31  D30  D29  D28  D27

 *            A4   A3   A2   A1   A0

 */

//

// LCD / Controller

//

#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)

  #if ENABLED(DOGLCD)

    #if ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0

      #if ENABLED(IS_MELZI)

        #define LCD_PINS_RS     30   // CS chip select /SS chip slave select

        #define LCD_PINS_ENABLE 29   // SID (MOSI)

        #define LCD_PINS_D4     17   // SCK (CLK) clock

        // Pin 27 is taken by LED_PIN, but Melzi LED does nothing with

        // Marlin so this can be used for BEEPER_PIN. You can use this pin

        // with M42 instead of BEEPER_PIN.

        #define BEEPER_PIN      27

      #else        // Sanguinololu >=1.3

        #define LCD_PINS_RS      4

        #define LCD_PINS_ENABLE 17

        #define LCD_PINS_D4     30

        #define LCD_PINS_D5     29

        #define LCD_PINS_D6     28

        #define LCD_PINS_D7     27

      #endif

    #else // DOGM SPI LCD Support

      #define DOGLCD_A0         30

      #define LCD_CONTRAST       1

      #if ENABLED(MAKRPANEL)

        #define BEEPER_PIN      29

        #define DOGLCD_CS       17

        #define LCD_BACKLIGHT_PIN 28   // PA3

      #elif ENABLED(IS_MELZI)

        #define BEEPER_PIN      27

        #define DOGLCD_CS       28

      #else // !MAKRPANEL

        #define DOGLCD_CS       29

      #endif

    #endif

    // Uncomment screen orientation

    #define LCD_SCREEN_ROT_0

    //#define LCD_SCREEN_ROT_90

    //#define LCD_SCREEN_ROT_180

    //#define LCD_SCREEN_ROT_270

  #else // !DOGLCD

    #define LCD_PINS_RS          4

    #define LCD_PINS_ENABLE     17

    #define LCD_PINS_D4         30

    #define LCD_PINS_D5         29

    #define LCD_PINS_D6         28

    #define LCD_PINS_D7         27

  #endif // !DOGLCD

  #define BTN_EN1               11

  #define BTN_EN2               10

  #if ENABLED(LCD_I2C_PANELOLU2)

    #if ENABLED(IS_MELZI)

      #define BTN_ENC           29

      #define LCD_SDSS          30   // Panelolu2 SD card reader rather than the Melzi

    #else

      #define BTN_ENC           30

    #endif

  #elif ENABLED(LCD_FOR_MELZI)

    #define LCD_PINS_RS         17

    #define LCD_PINS_ENABLE     16

    #define LCD_PINS_D4         11

    #define BTN_ENC             28

    #define BTN_EN1             29

    #define BTN_EN2             30

    #ifndef ST7920_DELAY_1

      #define ST7920_DELAY_1 DELAY_NS(0)

    #endif

    #ifndef ST7920_DELAY_2

      #define ST7920_DELAY_2 DELAY_NS(188)

    #endif

    #ifndef ST7920_DELAY_3

      #define ST7920_DELAY_3 DELAY_NS(0)

    #endif

  #elif ENABLED(ZONESTAR_LCD) // For the Tronxy Melzi boards

    #define LCD_PINS_RS         28

    #define LCD_PINS_ENABLE     29

    #define LCD_PINS_D4         10

    #define LCD_PINS_D5         11

    #define LCD_PINS_D6         16

    #define LCD_PINS_D7         17

    #define ADC_KEYPAD_PIN       1

    // Not used

    #define BTN_EN1             -1

    #define BTN_EN2             -1

  #else  // !LCD_I2C_PANELOLU2 && !LCD_FOR_MELZI && !ZONESTAR_LCD

    #define BTN_ENC             16

    #define LCD_SDSS            28   // Smart Controller SD card reader rather than the Melzi

  #endif

  #define SD_DETECT_PIN         -1

#endif // ULTRA_LCD && NEWPANEL

//

// M3/M4/M5 - Spindle/Laser Control

//

#if ENABLED(SPINDLE_LASER_ENABLE)

  #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL))  // try to use IO Header

    #define SPINDLE_LASER_ENABLE_PIN 10   // Pin should have a pullup/pulldown!

    #define SPINDLE_LASER_PWM_PIN     4   // MUST BE HARDWARE PWM

    #define SPINDLE_DIR_PIN          11

  #elif !MB(MELZI)  // use X stepper motor socket

    /**

     *  To control the spindle speed and have an LCD you must sacrifice

     *  the Extruder and pull some signals off the X stepper driver socket.

     *

     *  The following assumes:

     *   - The X stepper driver socket is empty

     *   - The extruder driver socket has a driver board plugged into it

     *   - The X stepper wires are attached the the extruder connector

     */

    /**

     *  Where to get the spindle signals

     *

     *      spindle signal          socket name       socket name

     *                                         -------

     *                               /ENABLE  O|     |O  VMOT

     *                                   MS1  O|     |O  GND

     *                                   MS2  O|     |O  2B

     *                                   MS3  O|     |O  2A

     *                                /RESET  O|     |O  1A

     *                                /SLEEP  O|     |O  1B

     *  SPINDLE_LASER_PWM_PIN           STEP  O|     |O  VDD

     *  SPINDLE_LASER_ENABLE_PIN         DIR  O|     |O  GND

     *                                         -------

     *

     *  Note: Socket names vary from vendor to vendor.

     */

    #undef X_DIR_PIN

    #undef X_ENABLE_PIN

    #undef X_STEP_PIN

    #define X_DIR_PIN                 0

    #define X_ENABLE_PIN             14

    #define X_STEP_PIN                1

    #define SPINDLE_LASER_PWM_PIN    15   // MUST BE HARDWARE PWM

    #define SPINDLE_LASER_ENABLE_PIN 21   // Pin should have a pullup!

    #define SPINDLE_DIR_PIN          -1   // No pin available on the socket for the direction pin

  #endif

#endif // SPINDLE_LASER_ENABLE