Subversion Repositories Tronxy-X3A-Marlin

/**

 * Marlin 3D Printer Firmware

 * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]

 *

 * Based on Sprinter and grbl.

 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm

 *

 * This program is free software: you can redistribute it and/or modify

 * it under the terms of the GNU General Public License as published by

 * the Free Software Foundation, either version 3 of the License, or

 * (at your option) any later version.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 *

 * You should have received a copy of the GNU General Public License

 * along with this program.  If not, see <http://www.gnu.org/licenses/>.

 *

 */

/**

 *  Rev B  2 JUN 2017

 *

 *  Converted to Arduino pin numbering

 */

/**

 *  There are two Arduino IDE extensions that are compatible with this board

 *  and with the mainstream Marlin software.

 *

 *  Teensyduino - http://www.pjrc.com/teensy/teensyduino.html

 *    Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu

 *

 *    Installation instructions are at the above URL.  Don't bother loading the

 *    libraries - they are not used with the Marlin software.

 *

 *  Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support

 *

 *    Installation:

 *

 *       1. Go to the above URL, click on the "Clone or Download" button and then

 *          click on "Download ZIP" button.

 *       2. Unzip the file, find the "printrboard" directory and then copy it to the

 *          hardware directory in Arduino.  The Arduino hardware directory will probably

 *          be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware.

 *       3. Restart Arduino.

 *       4. Select "Printrboard" from the 'Tools -> Boards' menu.

 *

 *  Teensyduino is the most popular option. Printrboard is used if your board doesn't have

 *  the Teensyduino bootloader on it.

 */

/**

 *  To burn the bootloader that comes with Printrboard:

 *

 *   1. Connect your programmer to the board.

 *   2. In the Arduino IDE select "Printrboard" and then select the programmer.

 *   3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.

 *   4. The programmer is no longer needed. Remove it.

 */

#ifndef __AVR_AT90USB1286__

  #error "Oops!  Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu."

#endif

#define DEFAULT_MACHINE_NAME    "SAV MkI"

#define DEFAULT_SOURCE_CODE_URL "https://github.com/fmalpartida/Marlin/tree/SAV-MkI-config"

#define BOARD_NAME              "SAV MkI"

//

// Servos

//

#define SERVO0_PIN         39   // F1  In teensy's pin definition for pinMode (in servo.cpp)

//

// Limit Switches

//

#define X_STOP_PIN         25   // B5

#define Y_STOP_PIN         26   // B6

//#define Z_STOP_PIN         27   // B7

#define Z_STOP_PIN         36   // E4 For inductive sensor.

//#define E_STOP_PIN         36   // E4

//

// Steppers

//

#define X_STEP_PIN         28   // A0

#define X_DIR_PIN          29   // A1

#define X_ENABLE_PIN       19   // E7

#define Y_STEP_PIN         30   // A2

#define Y_DIR_PIN          31   // A3

#define Y_ENABLE_PIN       18   // E6

#define Z_STEP_PIN         32   // A4

#define Z_DIR_PIN          33   // A5

#define Z_ENABLE_PIN       17   // C7

#define E0_STEP_PIN        34   // A6

#define E0_DIR_PIN         35   // A7

#define E0_ENABLE_PIN      13   // C3

//

// Temperature Sensors

//

#define TEMP_0_PIN          7   // F7  Analog Input (Extruder)

#define TEMP_BED_PIN        6   // F6  Analog Input (Bed)

//

// Heaters / Fans

//

#define HEATER_0_PIN       15   // C5 PWM3B - Extruder

#define HEATER_BED_PIN     14   // C4 PWM3C - Bed

#ifndef FAN_PIN

  #define FAN_PIN          16   // C6 PWM3A

#endif

//

// Misc. Functions

//

#define SDSS               20   // B0

// Extension header pin mapping

// ----------------------------

//  SCL (I2C)-D0    A0 (An), IO

//  SDA (I2C)-D1    A1 (An), IO

//  RX1-D2          A2 (An), IO

//  TX1-D3          A3 (An), IO

//  PWM-D24         A4 (An), IO

//  5V              GND

//  12V             GND

#define EXT_AUX_SCL_D0      0   // D0  PWM0B

#define EXT_AUX_SDA_D1      1   // D1

#define EXT_AUX_RX1_D2      2   // D2

#define EXT_AUX_TX1_D3      3   // D3

#define EXT_AUX_PWM_D24    24   // B4  PWM2A

#define EXT_AUX_A0          0   // F0  Analog Input

#define EXT_AUX_A0_IO      38   // F0  Digital IO

#define EXT_AUX_A1          1   // F1  Analog Input

#define EXT_AUX_A1_IO      39   // F1  Digital IO

#define EXT_AUX_A2          2   // F2  Analog Input

#define EXT_AUX_A2_IO      40   // F2  Digital IO

#define EXT_AUX_A3          3   // F3  Analog Input

#define EXT_AUX_A3_IO      41   // F3  Digital IO

#define EXT_AUX_A4          4   // F4  Analog Input

#define EXT_AUX_A4_IO      42   // F4  Digital IO

//

// LCD / Controller

//

#define BEEPER_PIN         -1

#define LCD_PINS_RS        -1

#define LCD_PINS_ENABLE    -1

#if ENABLED(SAV_3DLCD)

  // For LCD SHIFT register LCD

  #define SR_DATA_PIN      EXT_AUX_SDA_D1

  #define SR_CLK_PIN       EXT_AUX_SCL_D0

#endif

#if ENABLED(SAV_3DLCD) || ENABLED(SAV_3DGLCD)

  #define BTN_EN1          EXT_AUX_A1_IO

  #define BTN_EN2          EXT_AUX_A0_IO

  #define BTN_ENC          EXT_AUX_PWM_D24

  #define KILL_PIN         EXT_AUX_A2_IO

  #define HOME_PIN         EXT_AUX_A4_IO

#else // Use the expansion header for spindle control

  //

  // M3/M4/M5 - Spindle/Laser Control

  //

  #define SPINDLE_LASER_PWM_PIN    24   // B4  PWM2A

  #define SPINDLE_LASER_ENABLE_PIN 39   // F1  Pin should have a pullup!

  #define SPINDLE_DIR_PIN          40   // F2

  #define CASE_LIGHT_PIN            0   // D0  PWM0B

#endif