| 1 |
ron |
1 |
/**
|
|
|
2 |
* Marlin 3D Printer Firmware
|
|
|
3 |
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
4 |
*
|
|
|
5 |
* Based on Sprinter and grbl.
|
|
|
6 |
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
|
7 |
*
|
|
|
8 |
* This program is free software: you can redistribute it and/or modify
|
|
|
9 |
* it under the terms of the GNU General Public License as published by
|
|
|
10 |
* the Free Software Foundation, either version 3 of the License, or
|
|
|
11 |
* (at your option) any later version.
|
|
|
12 |
*
|
|
|
13 |
* This program is distributed in the hope that it will be useful,
|
|
|
14 |
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
15 |
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
16 |
* GNU General Public License for more details.
|
|
|
17 |
*
|
|
|
18 |
* You should have received a copy of the GNU General Public License
|
|
|
19 |
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
20 |
*
|
|
|
21 |
*/
|
|
|
22 |
|
|
|
23 |
/**
|
|
|
24 |
* SdFatConfig.h
|
|
|
25 |
* Arduino SdFat Library
|
|
|
26 |
* Copyright (C) 2009 by William Greiman
|
|
|
27 |
*
|
|
|
28 |
* This file is part of the Arduino Sd2Card Library
|
|
|
29 |
*/
|
|
|
30 |
|
|
|
31 |
#ifndef _SDFATCONFIG_H_
|
|
|
32 |
#define _SDFATCONFIG_H_
|
|
|
33 |
|
|
|
34 |
#include "MarlinConfig.h"
|
|
|
35 |
|
|
|
36 |
/**
|
|
|
37 |
* To use multiple SD cards set USE_MULTIPLE_CARDS nonzero.
|
|
|
38 |
*
|
|
|
39 |
* Using multiple cards costs 400 - 500 bytes of flash.
|
|
|
40 |
*
|
|
|
41 |
* Each card requires about 550 bytes of SRAM so use of a Mega is recommended.
|
|
|
42 |
*/
|
|
|
43 |
#define USE_MULTIPLE_CARDS 0
|
|
|
44 |
|
|
|
45 |
/**
|
|
|
46 |
* Call flush for endl if ENDL_CALLS_FLUSH is nonzero
|
|
|
47 |
*
|
|
|
48 |
* The standard for iostreams is to call flush. This is very costly for
|
|
|
49 |
* SdFat. Each call to flush causes 2048 bytes of I/O to the SD.
|
|
|
50 |
*
|
|
|
51 |
* SdFat has a single 512 byte buffer for SD I/O so it must write the current
|
|
|
52 |
* data block to the SD, read the directory block from the SD, update the
|
|
|
53 |
* directory entry, write the directory block to the SD and read the data
|
|
|
54 |
* block back into the buffer.
|
|
|
55 |
*
|
|
|
56 |
* The SD flash memory controller is not designed for this many rewrites
|
|
|
57 |
* so performance may be reduced by more than a factor of 100.
|
|
|
58 |
*
|
|
|
59 |
* If ENDL_CALLS_FLUSH is zero, you must call flush and/or close to force
|
|
|
60 |
* all data to be written to the SD.
|
|
|
61 |
*/
|
|
|
62 |
#define ENDL_CALLS_FLUSH 0
|
|
|
63 |
|
|
|
64 |
/**
|
|
|
65 |
* Allow FAT12 volumes if FAT12_SUPPORT is nonzero.
|
|
|
66 |
* FAT12 has not been well tested.
|
|
|
67 |
*/
|
|
|
68 |
#define FAT12_SUPPORT 0
|
|
|
69 |
|
|
|
70 |
/**
|
|
|
71 |
* SPI init rate for SD initialization commands. Must be 5 (F_CPU/64)
|
|
|
72 |
* or 6 (F_CPU/128).
|
|
|
73 |
*/
|
|
|
74 |
#define SPI_SD_INIT_RATE 5
|
|
|
75 |
|
|
|
76 |
/**
|
|
|
77 |
* Set the SS pin high for hardware SPI. If SS is chip select for another SPI
|
|
|
78 |
* device this will disable that device during the SD init phase.
|
|
|
79 |
*/
|
|
|
80 |
#define SET_SPI_SS_HIGH 1
|
|
|
81 |
|
|
|
82 |
/**
|
|
|
83 |
* Define MEGA_SOFT_SPI nonzero to use software SPI on Mega Arduinos.
|
|
|
84 |
* Pins used are SS 10, MOSI 11, MISO 12, and SCK 13.
|
|
|
85 |
*
|
|
|
86 |
* MEGA_SOFT_SPI allows an unmodified Adafruit GPS Shield to be used
|
|
|
87 |
* on Mega Arduinos. Software SPI works well with GPS Shield V1.1
|
|
|
88 |
* but many SD cards will fail with GPS Shield V1.0.
|
|
|
89 |
*/
|
|
|
90 |
#define MEGA_SOFT_SPI 0
|
|
|
91 |
|
|
|
92 |
// Set USE_SOFTWARE_SPI nonzero to ALWAYS use Software SPI.
|
|
|
93 |
#define USE_SOFTWARE_SPI 0
|
|
|
94 |
|
|
|
95 |
// Define software SPI pins so Mega can use unmodified 168/328 shields
|
|
|
96 |
#define SOFT_SPI_CS_PIN 10 // Software SPI chip select pin for the SD
|
|
|
97 |
#define SOFT_SPI_MOSI_PIN 11 // Software SPI Master Out Slave In pin
|
|
|
98 |
#define SOFT_SPI_MISO_PIN 12 // Software SPI Master In Slave Out pin
|
|
|
99 |
#define SOFT_SPI_SCK_PIN 13 // Software SPI Clock pin
|
|
|
100 |
|
|
|
101 |
/**
|
|
|
102 |
* The __cxa_pure_virtual function is an error handler that is invoked when
|
|
|
103 |
* a pure virtual function is called.
|
|
|
104 |
*/
|
|
|
105 |
#define USE_CXA_PURE_VIRTUAL 1
|
|
|
106 |
|
|
|
107 |
/**
|
|
|
108 |
* Defines for 8.3 and long (vfat) filenames
|
|
|
109 |
*/
|
|
|
110 |
|
|
|
111 |
#define FILENAME_LENGTH 13 // Number of UTF-16 characters per entry
|
|
|
112 |
|
|
|
113 |
// Total bytes needed to store a single long filename
|
|
|
114 |
#define LONG_FILENAME_LENGTH (FILENAME_LENGTH * MAX_VFAT_ENTRIES + 1)
|
|
|
115 |
|
|
|
116 |
#endif // _SDFATCONFIG_H_
|