| 1 |
ron |
1 |
/**
|
|
|
2 |
* Marlin 3D Printer Firmware
|
|
|
3 |
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
4 |
*
|
|
|
5 |
* Based on Sprinter and grbl.
|
|
|
6 |
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
|
7 |
*
|
|
|
8 |
* This program is free software: you can redistribute it and/or modify
|
|
|
9 |
* it under the terms of the GNU General Public License as published by
|
|
|
10 |
* the Free Software Foundation, either version 3 of the License, or
|
|
|
11 |
* (at your option) any later version.
|
|
|
12 |
*
|
|
|
13 |
* This program is distributed in the hope that it will be useful,
|
|
|
14 |
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
15 |
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
16 |
* GNU General Public License for more details.
|
|
|
17 |
*
|
|
|
18 |
* You should have received a copy of the GNU General Public License
|
|
|
19 |
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
20 |
*
|
|
|
21 |
*/
|
|
|
22 |
|
|
|
23 |
/**
|
|
|
24 |
* Cheaptronic v1.0 pin assignments
|
|
|
25 |
*/
|
|
|
26 |
|
|
|
27 |
#ifndef __AVR_ATmega2560__
|
|
|
28 |
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
|
|
|
29 |
#endif
|
|
|
30 |
|
|
|
31 |
#define BOARD_NAME "Cheaptronic v1.0"
|
|
|
32 |
//
|
|
|
33 |
// Limit Switches
|
|
|
34 |
//
|
|
|
35 |
#define X_STOP_PIN 3
|
|
|
36 |
#define Y_STOP_PIN 2
|
|
|
37 |
#define Z_STOP_PIN 5
|
|
|
38 |
|
|
|
39 |
//
|
|
|
40 |
// Steppers
|
|
|
41 |
//
|
|
|
42 |
#define X_STEP_PIN 14
|
|
|
43 |
#define X_DIR_PIN 15
|
|
|
44 |
#define X_ENABLE_PIN 24
|
|
|
45 |
|
|
|
46 |
#define Y_STEP_PIN 35
|
|
|
47 |
#define Y_DIR_PIN 36
|
|
|
48 |
#define Y_ENABLE_PIN 31
|
|
|
49 |
|
|
|
50 |
#define Z_STEP_PIN 40
|
|
|
51 |
#define Z_DIR_PIN 41
|
|
|
52 |
#define Z_ENABLE_PIN 37
|
|
|
53 |
|
|
|
54 |
#define E0_STEP_PIN 26
|
|
|
55 |
#define E0_DIR_PIN 28
|
|
|
56 |
#define E0_ENABLE_PIN 25
|
|
|
57 |
|
|
|
58 |
#define E1_STEP_PIN 33
|
|
|
59 |
#define E1_DIR_PIN 34
|
|
|
60 |
#define E1_ENABLE_PIN 30
|
|
|
61 |
|
|
|
62 |
//
|
|
|
63 |
// Temperature sensors
|
|
|
64 |
//
|
|
|
65 |
#define TEMP_0_PIN 15 // Analog Input
|
|
|
66 |
#define TEMP_1_PIN 14 // Analog Input
|
|
|
67 |
#define TEMP_BED_PIN 13 // Analog Input
|
|
|
68 |
|
|
|
69 |
//
|
|
|
70 |
// Heaters / Fans
|
|
|
71 |
//
|
|
|
72 |
#define HEATER_0_PIN 19 // EXTRUDER 1
|
|
|
73 |
#define HEATER_1_PIN 23 // EXTRUDER 2
|
|
|
74 |
#define HEATER_BED_PIN 22
|
|
|
75 |
|
|
|
76 |
//
|
|
|
77 |
// LCD / Controller
|
|
|
78 |
//
|
|
|
79 |
// Cheaptronic v1.0 doesn't support LCD
|
|
|
80 |
#define LCD_PINS_RS -1
|
|
|
81 |
#define LCD_PINS_ENABLE -1
|
|
|
82 |
|
|
|
83 |
// Cheaptronic v1.0 doesn't support keypad
|
|
|
84 |
#define BTN_EN1 -1
|
|
|
85 |
#define BTN_EN2 -1
|
|
|
86 |
#define BTN_ENC -1
|