| 1 |
ron |
1 |
/**
|
|
|
2 |
* Marlin 3D Printer Firmware
|
|
|
3 |
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
4 |
*
|
|
|
5 |
* Based on Sprinter and grbl.
|
|
|
6 |
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
|
7 |
*
|
|
|
8 |
* This program is free software: you can redistribute it and/or modify
|
|
|
9 |
* it under the terms of the GNU General Public License as published by
|
|
|
10 |
* the Free Software Foundation, either version 3 of the License, or
|
|
|
11 |
* (at your option) any later version.
|
|
|
12 |
*
|
|
|
13 |
* This program is distributed in the hope that it will be useful,
|
|
|
14 |
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
15 |
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
16 |
* GNU General Public License for more details.
|
|
|
17 |
*
|
|
|
18 |
* You should have received a copy of the GNU General Public License
|
|
|
19 |
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
20 |
*
|
|
|
21 |
*/
|
|
|
22 |
|
|
|
23 |
/**
|
|
|
24 |
* Gen6 pin assignments
|
|
|
25 |
*/
|
|
|
26 |
|
|
|
27 |
/**
|
|
|
28 |
* Rev B 26 DEC 2016
|
|
|
29 |
*
|
|
|
30 |
* 1) added pointer to a current Arduino IDE extension
|
|
|
31 |
* 2) added support for M3, M4 & M5 spindle control commands
|
|
|
32 |
* 3) added case light pin definition
|
|
|
33 |
*
|
|
|
34 |
*/
|
|
|
35 |
|
|
|
36 |
/**
|
|
|
37 |
* A useable Arduino IDE extension (board manager) can be found at
|
|
|
38 |
* https://github.com/Lauszus/Sanguino
|
|
|
39 |
*
|
|
|
40 |
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
|
|
41 |
*
|
|
|
42 |
* Here's the JSON path:
|
|
|
43 |
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
|
|
44 |
*
|
|
|
45 |
* When installing select 1.0.2
|
|
|
46 |
*
|
|
|
47 |
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
|
|
48 |
* Just use the above JSON URL instead of Sparkfun's JSON.
|
|
|
49 |
*
|
|
|
50 |
* Once installed select the Sanguino board and then select the CPU.
|
|
|
51 |
*
|
|
|
52 |
*/
|
|
|
53 |
|
|
|
54 |
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
|
|
|
55 |
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
|
|
56 |
#endif
|
|
|
57 |
|
|
|
58 |
#ifndef BOARD_NAME
|
|
|
59 |
#define BOARD_NAME "Gen6"
|
|
|
60 |
#endif
|
|
|
61 |
|
|
|
62 |
//
|
|
|
63 |
// Limit Switches
|
|
|
64 |
//
|
|
|
65 |
#define X_STOP_PIN 20
|
|
|
66 |
#define Y_STOP_PIN 25
|
|
|
67 |
#define Z_STOP_PIN 30
|
|
|
68 |
|
|
|
69 |
//
|
|
|
70 |
// Steppers
|
|
|
71 |
//
|
|
|
72 |
#define X_STEP_PIN 15
|
|
|
73 |
#define X_DIR_PIN 18
|
|
|
74 |
#define X_ENABLE_PIN 19
|
|
|
75 |
|
|
|
76 |
#define Y_STEP_PIN 23
|
|
|
77 |
#define Y_DIR_PIN 22
|
|
|
78 |
#define Y_ENABLE_PIN 24
|
|
|
79 |
|
|
|
80 |
#define Z_STEP_PIN 27
|
|
|
81 |
#define Z_DIR_PIN 28
|
|
|
82 |
#define Z_ENABLE_PIN 29
|
|
|
83 |
|
|
|
84 |
#define E0_STEP_PIN 4 // Edited @ EJE Electronics 20100715
|
|
|
85 |
#define E0_DIR_PIN 2 // Edited @ EJE Electronics 20100715
|
|
|
86 |
#define E0_ENABLE_PIN 3 // Added @ EJE Electronics 20100715
|
|
|
87 |
|
|
|
88 |
//
|
|
|
89 |
// Temperature Sensor
|
|
|
90 |
//
|
|
|
91 |
#define TEMP_0_PIN 5 // Analog Input
|
|
|
92 |
|
|
|
93 |
//
|
|
|
94 |
// Heaters
|
|
|
95 |
//
|
|
|
96 |
#define HEATER_0_PIN 14 // changed @ rkoeppl 20110410
|
|
|
97 |
|
|
|
98 |
#if !MB(GEN6)
|
|
|
99 |
#define HEATER_BED_PIN 1 // changed @ rkoeppl 20110410
|
|
|
100 |
#define TEMP_BED_PIN 0 // Analog Input
|
|
|
101 |
#endif
|
|
|
102 |
|
|
|
103 |
//
|
|
|
104 |
// Misc. Functions
|
|
|
105 |
//
|
|
|
106 |
#define SDSS 17
|
|
|
107 |
#define DEBUG_PIN 0
|
|
|
108 |
#define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM
|
|
|
109 |
|
|
|
110 |
// RS485 pins
|
|
|
111 |
#define TX_ENABLE_PIN 12
|
|
|
112 |
#define RX_ENABLE_PIN 13
|
|
|
113 |
|
|
|
114 |
//
|
|
|
115 |
// M3/M4/M5 - Spindle/Laser Control
|
|
|
116 |
//
|
|
|
117 |
#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup/pulldown!
|
|
|
118 |
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
|
|
|
119 |
#define SPINDLE_DIR_PIN 6
|