Subversion Repositories MK-Marlin

/**

 * Marlin 3D Printer Firmware

 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]

 *

 * Based on Sprinter and grbl.

 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm

 *

 * This program is free software: you can redistribute it and/or modify

 * it under the terms of the GNU General Public License as published by

 * the Free Software Foundation, either version 3 of the License, or

 * (at your option) any later version.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 *

 * You should have received a copy of the GNU General Public License

 * along with this program.  If not, see <http://www.gnu.org/licenses/>.

 *

 */

/**

 * Minitronics v1.0/1.1 pin assignments

 */

/**

 * Rev B   2 JAN 2017

 *

 *  Added pin definitions for M3, M4 & M5 spindle control commands

 *

 */

#ifndef __AVR_ATmega1281__

  #error "Oops!  Make sure you have 'Minitronics' selected from the 'Tools -> Boards' menu."

#endif

#if HOTENDS > 2 || E_STEPPERS > 2

  #error "Minitronics supports up to 2 hotends / E-steppers. Comment out this line to continue."

#endif

#define BOARD_NAME         "Minitronics v1.0 / v1.1"

//

// Limit Switches

//

#define X_MIN_PIN           5

#define X_MAX_PIN           2

#define Y_MIN_PIN           2

#define Y_MAX_PIN          15

#define Z_MIN_PIN           6

#define Z_MAX_PIN          -1

//

// Steppers

//

#define X_STEP_PIN         48

#define X_DIR_PIN          47

#define X_ENABLE_PIN       49

#define Y_STEP_PIN         39   // A6

#define Y_DIR_PIN          40   // A0

#define Y_ENABLE_PIN       38

#define Z_STEP_PIN         42   // A2

#define Z_DIR_PIN          43   // A6

#define Z_ENABLE_PIN       41   // A1

#define E0_STEP_PIN        45

#define E0_DIR_PIN         44

#define E0_ENABLE_PIN      27

#define E1_STEP_PIN        36

#define E1_DIR_PIN         35

#define E1_ENABLE_PIN      37

//

// Temperature Sensors

//

#define TEMP_0_PIN          7   // Analog Input

#define TEMP_1_PIN          6   // Analog Input

#define TEMP_BED_PIN        6   // Analog Input

//

// Heaters / Fans

//

#define HEATER_0_PIN        7   // EXTRUDER 1

#define HEATER_1_PIN        8   // EXTRUDER 2

#define HEATER_BED_PIN      3   // BED

#ifndef FAN_PIN

  #define FAN_PIN           9

#endif

//

// Misc. Functions

//

#define SDSS               16

#define LED_PIN            46

//

// LCD / Controller

//

#define BEEPER_PIN         -1

#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)

  #define LCD_PINS_RS      15   // CS chip select /SS chip slave select

  #define LCD_PINS_ENABLE  11   // SID (MOSI)

  #define LCD_PINS_D4      10   // SCK (CLK) clock

  #define BTN_EN1          18

  #define BTN_EN2          17

  #define BTN_ENC          25

  #define SD_DETECT_PIN    30

#else

  #define LCD_PINS_RS      -1

  #define LCD_PINS_ENABLE  -1

  // Buttons are directly attached using keypad

  #define BTN_EN1          -1

  #define BTN_EN2          -1

  #define BTN_ENC          -1

  #define SD_DETECT_PIN    -1   // Minitronics doesn't use this

#endif

//

// M3/M4/M5 - Spindle/Laser Control

//

#if ENABLED(SPINDLE_LASER_ENABLE)  // assumes we're only doing CNC work (no 3D printing)

  #undef HEATER_BED_PIN

  #undef TEMP_BED_PIN             // need to free up some pins but also need to

  #undef TEMP_0_PIN               // re-assign them (to unused pins) because Marlin

  #undef TEMP_1_PIN               // requires the presence of certain pins or else it

  #define HEATER_BED_PIN      4   // won't compile

  #define TEMP_BED_PIN       50

  #define TEMP_0_PIN         51

  #define SPINDLE_LASER_ENABLE_PIN      52   // using A6 because it already has a pullup

  #define SPINDLE_LASER_PWM_PIN          3   // WARNING - LED & resistor pull up to +12/+24V stepper voltage

  #define SPINDLE_DIR_PIN               53

#endif