| 1 |
ron |
1 |
/**
|
|
|
2 |
* Marlin 3D Printer Firmware
|
|
|
3 |
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
4 |
*
|
|
|
5 |
* Based on Sprinter and grbl.
|
|
|
6 |
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
|
7 |
*
|
|
|
8 |
* This program is free software: you can redistribute it and/or modify
|
|
|
9 |
* it under the terms of the GNU General Public License as published by
|
|
|
10 |
* the Free Software Foundation, either version 3 of the License, or
|
|
|
11 |
* (at your option) any later version.
|
|
|
12 |
*
|
|
|
13 |
* This program is distributed in the hope that it will be useful,
|
|
|
14 |
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
15 |
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
16 |
* GNU General Public License for more details.
|
|
|
17 |
*
|
|
|
18 |
* You should have received a copy of the GNU General Public License
|
|
|
19 |
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
20 |
*
|
|
|
21 |
*/
|
|
|
22 |
|
|
|
23 |
/**
|
|
|
24 |
* Open Motion controller with enable based extruders (Alpha!)
|
|
|
25 |
*
|
|
|
26 |
* ATMega644
|
|
|
27 |
*
|
|
|
28 |
* +---\/---+
|
|
|
29 |
* (D 0) PB0 1| |40 PA0 (AI 0 / D31)
|
|
|
30 |
* (D 1) PB1 2| |39 PA1 (AI 1 / D30)
|
|
|
31 |
* INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
|
|
|
32 |
* PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
|
|
|
33 |
* PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
|
|
|
34 |
* MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
|
|
|
35 |
* MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
|
|
|
36 |
* SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
|
|
|
37 |
* RST 9| |32 AREF
|
|
|
38 |
* VCC 10| |31 GND
|
|
|
39 |
* GND 11| |30 AVCC
|
|
|
40 |
* XTAL2 12| |29 PC7 (D 23)
|
|
|
41 |
* XTAL1 13| |28 PC6 (D 22)
|
|
|
42 |
* RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
|
|
|
43 |
* TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
|
|
|
44 |
* INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
|
|
|
45 |
* INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
|
|
|
46 |
* PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
|
|
|
47 |
* PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
|
|
|
48 |
* PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
|
|
|
49 |
* +--------+
|
|
|
50 |
*
|
|
|
51 |
*/
|
|
|
52 |
|
|
|
53 |
/**
|
|
|
54 |
* Rev B 26 DEC 2016
|
|
|
55 |
*
|
|
|
56 |
* added pointer to a current Arduino IDE extension
|
|
|
57 |
*
|
|
|
58 |
*/
|
|
|
59 |
|
|
|
60 |
/**
|
|
|
61 |
* A useable Arduino IDE extension (board manager) can be found at
|
|
|
62 |
* https://github.com/Lauszus/Sanguino
|
|
|
63 |
*
|
|
|
64 |
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
|
|
65 |
*
|
|
|
66 |
* Here's the JSON path:
|
|
|
67 |
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
|
|
68 |
*
|
|
|
69 |
* When installing select 1.0.2
|
|
|
70 |
*
|
|
|
71 |
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
|
|
72 |
* Just use the above JSON URL instead of Sparkfun's JSON.
|
|
|
73 |
*
|
|
|
74 |
* Once installed select the Sanguino board and then select the CPU.
|
|
|
75 |
*
|
|
|
76 |
*/
|
|
|
77 |
|
|
|
78 |
#ifndef __AVR_ATmega644__
|
|
|
79 |
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
|
|
80 |
#endif
|
|
|
81 |
|
|
|
82 |
#define BOARD_NAME "Alpha OMCA"
|
|
|
83 |
|
|
|
84 |
//
|
|
|
85 |
// Limit Switches
|
|
|
86 |
//
|
|
|
87 |
#define X_STOP_PIN 0
|
|
|
88 |
#define Y_STOP_PIN 1
|
|
|
89 |
#define Z_STOP_PIN 2
|
|
|
90 |
|
|
|
91 |
//
|
|
|
92 |
// Steppers
|
|
|
93 |
//
|
|
|
94 |
#define X_STEP_PIN 21
|
|
|
95 |
#define X_DIR_PIN 20
|
|
|
96 |
#define X_ENABLE_PIN 24
|
|
|
97 |
|
|
|
98 |
#define Y_STEP_PIN 23
|
|
|
99 |
#define Y_DIR_PIN 22
|
|
|
100 |
#define Y_ENABLE_PIN 24
|
|
|
101 |
|
|
|
102 |
#define Z_STEP_PIN 26
|
|
|
103 |
#define Z_DIR_PIN 25
|
|
|
104 |
#define Z_ENABLE_PIN 24
|
|
|
105 |
|
|
|
106 |
#define E0_STEP_PIN 28
|
|
|
107 |
#define E0_DIR_PIN 27
|
|
|
108 |
#define E0_ENABLE_PIN 24
|
|
|
109 |
|
|
|
110 |
#define E1_STEP_PIN -1 // 19
|
|
|
111 |
#define E1_DIR_PIN -1 // 18
|
|
|
112 |
#define E1_ENABLE_PIN 24
|
|
|
113 |
|
|
|
114 |
#define E2_STEP_PIN -1 // 17
|
|
|
115 |
#define E2_DIR_PIN -1 // 16
|
|
|
116 |
#define E2_ENABLE_PIN 24
|
|
|
117 |
|
|
|
118 |
//
|
|
|
119 |
// Temperature Sensors
|
|
|
120 |
//
|
|
|
121 |
#define TEMP_0_PIN 0 // Analog Input (D27)
|
|
|
122 |
|
|
|
123 |
//
|
|
|
124 |
// Heaters / Fans
|
|
|
125 |
//
|
|
|
126 |
#define HEATER_0_PIN 4
|
|
|
127 |
|
|
|
128 |
#ifndef FAN_PIN
|
|
|
129 |
#define FAN_PIN 3
|
|
|
130 |
#endif
|
|
|
131 |
|
|
|
132 |
//
|
|
|
133 |
// Misc. Functions
|
|
|
134 |
//
|
|
|
135 |
#define SDSS 11
|
|
|
136 |
|
|
|
137 |
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
|