Blame | Last modification | View Log | RSS feed
/*** Marlin 3D Printer Firmware* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]** Based on Sprinter and grbl.* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm** This program is free software: you can redistribute it and/or modify* it under the terms of the GNU General Public License as published by* the Free Software Foundation, either version 3 of the License, or* (at your option) any later version.** This program is distributed in the hope that it will be useful,* but WITHOUT ANY WARRANTY; without even the implied warranty of* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the* GNU General Public License for more details.** You should have received a copy of the GNU General Public License* along with this program. If not, see <http://www.gnu.org/licenses/>.**//*** Einsy-Retro pin assignments*/#ifndef __AVR_ATmega2560__#error "Oops! Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu."#endif#define BOARD_NAME "Einsy Retro"//// TMC2130 Configuration_adv defaults for EinsyRetro//#if !AXIS_DRIVER_TYPE(X, TMC2130) || !AXIS_DRIVER_TYPE(Y, TMC2130) || !AXIS_DRIVER_TYPE(Z, TMC2130) || !AXIS_DRIVER_TYPE(E0, TMC2130)#error "You must set ([XYZ]|E0)_DRIVER_TYPE to TMC2130 in Configuration.h for EinsyRetro."#endif// TMC2130 Diag Pins (currently just for reference)#define X_DIAG_PIN 64#define Y_DIAG_PIN 69#define Z_DIAG_PIN 68#define E0_DIAG_PIN 65//// Limit Switches//// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers.// Otherwise use a physical endstop based configuration.//// SERVO0_PIN and Z_MIN_PIN configuration for BLTOUCH sensor when combined with SENSORLESS_HOMING.//#if DISABLED(SENSORLESS_HOMING)#define X_MIN_PIN 12#define Y_MIN_PIN 11#define Z_MIN_PIN 10#define X_MAX_PIN 81#define Y_MAX_PIN 57#else#if X_HOME_DIR == -1#define X_MIN_PIN X_DIAG_PIN#define X_MAX_PIN 81#else#define X_MIN_PIN 12#define X_MAX_PIN X_DIAG_PIN#endif#if Y_HOME_DIR == -1#define Y_MIN_PIN Y_DIAG_PIN#define Y_MAX_PIN 57#else#define Y_MIN_PIN 11#define Y_MAX_PIN Y_DIAG_PIN#endif#if ENABLED(BLTOUCH)#define Z_MIN_PIN 11 // Y-MIN#define SERVO0_PIN 10 // Z-MIN#else#define Z_MIN_PIN 10#endif#endif#define Z_MAX_PIN 7//// Z Probe (when not Z_MIN_PIN)//#ifndef Z_MIN_PROBE_PIN#define Z_MIN_PROBE_PIN 10#endif//// Steppers//#define X_STEP_PIN 37#define X_DIR_PIN 49#define X_ENABLE_PIN 29#define X_CS_PIN 41#define Y_STEP_PIN 36#define Y_DIR_PIN 48#define Y_ENABLE_PIN 28#define Y_CS_PIN 39#define Z_STEP_PIN 35#define Z_DIR_PIN 47#define Z_ENABLE_PIN 27#define Z_CS_PIN 67#define E0_STEP_PIN 34#define E0_DIR_PIN 43#define E0_ENABLE_PIN 26#define E0_CS_PIN 66//// Temperature Sensors//#define TEMP_0_PIN 0 // Analog Input#define TEMP_1_PIN 1 // Analog Input#define TEMP_BED_PIN 2 // Analog Input//// Heaters / Fans//#define HEATER_0_PIN 3#define HEATER_BED_PIN 4#ifndef FAN_PIN#define FAN_PIN 8#endif#define FAN1_PIN 6//// Misc. Functions//#define SDSS 53#define LED_PIN 13#define CASE_LIGHT_PIN 9//// M3/M4/M5 - Spindle/Laser Control//// use P1 connector for spindle pins#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM#define SPINDLE_LASER_ENABLE_PIN 18 // Pin should have a pullup!#define SPINDLE_DIR_PIN 19//// Průša i3 MK2 Multiplexer Support//#define E_MUX0_PIN 17#define E_MUX1_PIN 16#define E_MUX2_PIN 78 // 84 in MK2 Firmware, with BEEPER as 78//// LCD / Controller//#if ENABLED(ULTRA_LCD)#define KILL_PIN 32#if ENABLED(NEWPANEL)#if ENABLED(CR10_STOCKDISPLAY)#define LCD_PINS_RS 85#define LCD_PINS_ENABLE 71#define LCD_PINS_D4 70#define BTN_EN1 18#define BTN_EN2 19#else#define LCD_PINS_RS 82#define LCD_PINS_ENABLE 18#define LCD_PINS_D4 19#define LCD_PINS_D5 70#define LCD_PINS_D6 85#define LCD_PINS_D7 71#define BTN_EN1 14#define BTN_EN2 72#endif#define BTN_ENC 9 // AUX-2#define BEEPER_PIN 84 // AUX-4#define SD_DETECT_PIN 15#endif // NEWPANEL#endif // ULTRA_LCD