Blame | Last modification | View Log | RSS feed
/*** Marlin 3D Printer Firmware* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]** Based on Sprinter and grbl.* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm** This program is free software: you can redistribute it and/or modify* it under the terms of the GNU General Public License as published by* the Free Software Foundation, either version 3 of the License, or* (at your option) any later version.** This program is distributed in the hope that it will be useful,* but WITHOUT ANY WARRANTY; without even the implied warranty of* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the* GNU General Public License for more details.** You should have received a copy of the GNU General Public License* along with this program. If not, see <http://www.gnu.org/licenses/>.**//*** Mini-Rambo pin assignments*/#ifndef __AVR_ATmega2560__#error "Oops! Make sure you have 'Rambo' selected from the 'Tools -> Boards' menu."#endif#if MB(MINIRAMBO_10A)#define BOARD_NAME "Mini Rambo 1.0a"#else#define BOARD_NAME "Mini Rambo"#endif//// Limit Switches//#define X_MIN_PIN 12#define X_MAX_PIN 30#define Y_MIN_PIN 11#define Y_MAX_PIN 24#define Z_MIN_PIN 10#define Z_MAX_PIN 23//// Z Probe (when not Z_MIN_PIN)//#ifndef Z_MIN_PROBE_PIN#define Z_MIN_PROBE_PIN 23#endif//// Steppers//#define X_STEP_PIN 37#define X_DIR_PIN 48#define X_ENABLE_PIN 29#define Y_STEP_PIN 36#define Y_DIR_PIN 49#define Y_ENABLE_PIN 28#define Z_STEP_PIN 35#define Z_DIR_PIN 47#define Z_ENABLE_PIN 27#define E0_STEP_PIN 34#define E0_DIR_PIN 43#define E0_ENABLE_PIN 26// Microstepping pins - Mapping not from fastio.h (?)#define X_MS1_PIN 40#define X_MS2_PIN 41#define Y_MS1_PIN 69#define Y_MS2_PIN 39#define Z_MS1_PIN 68#define Z_MS2_PIN 67#define E0_MS1_PIN 65#define E0_MS2_PIN 66#define MOTOR_CURRENT_PWM_XY_PIN 46#define MOTOR_CURRENT_PWM_Z_PIN 45#define MOTOR_CURRENT_PWM_E_PIN 44// Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range#ifndef MOTOR_CURRENT_PWM_RANGE#define MOTOR_CURRENT_PWM_RANGE 2000#endif#define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250}//// Temperature Sensors//#define TEMP_0_PIN 0 // Analog Input#define TEMP_1_PIN 1 // Analog Input#define TEMP_BED_PIN 2 // Analog Input//// Heaters / Fans//#define HEATER_0_PIN 3#define HEATER_1_PIN 7#if !MB(MINIRAMBO_10A)#define HEATER_2_PIN 6#endif#define HEATER_BED_PIN 4#ifndef FAN_PIN#define FAN_PIN 8#endif#define FAN1_PIN 6//// Misc. Functions//#define SDSS 53#define LED_PIN 13#if !MB(MINIRAMBO_10A)#define CASE_LIGHT_PIN 9#endif//// M3/M4/M5 - Spindle/Laser Control//// use P1 connector for spindle pins#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM#define SPINDLE_LASER_ENABLE_PIN 18 // Pin should have a pullup!#define SPINDLE_DIR_PIN 19//// Průša i3 MK2 Multiplexer Support//#define E_MUX0_PIN 17#define E_MUX1_PIN 16#if !MB(MINIRAMBO_10A)#define E_MUX2_PIN 78 // 84 in MK2 Firmware, with BEEPER as 78#endif//// LCD / Controller//#if ENABLED(ULTRA_LCD)#if !MB(MINIRAMBO_10A)#define KILL_PIN 32#endif#if ENABLED(NEWPANEL)#if MB(MINIRAMBO_10A)#define BEEPER_PIN 78#define BTN_EN1 80#define BTN_EN2 73#define BTN_ENC 21#define LCD_PINS_RS 38#define LCD_PINS_ENABLE 5#define LCD_PINS_D4 14#define LCD_PINS_D5 15#define LCD_PINS_D6 32#define LCD_PINS_D7 31#define SD_DETECT_PIN 72#else // !MINIRAMBO_10A// AUX-4#define BEEPER_PIN 84// AUX-2#define BTN_EN1 14#define BTN_EN2 72#define BTN_ENC 9#define LCD_PINS_RS 82#define LCD_PINS_ENABLE 18#define LCD_PINS_D4 19#define LCD_PINS_D5 70#define LCD_PINS_D6 85#define LCD_PINS_D7 71#define SD_DETECT_PIN 15#endif // !MINIRAMBO_10A#endif // NEWPANEL#endif // ULTRA_LCD